Polymeric nanoparticles (NP) consisting of Poly Lactic-co-lactic acid - methyl polyethylene glycol (PLLA-mPEG) or Poly Lactic-co-Glycolic Acid (PLGA) are an emerging field of study for therapeutic and diagnostic applications. NPs have a variety of tunable physical characteristics like size, morphology, and surface topography. They can be loaded with therapeutic and/or diagnostic agents, either on the surface or within the core. NP size is an important characteristic as it directly impacts clearance and where the particles can travel and bind in the body. To that end, the typical target size for NPs is 30-200 nm for the majority of applications. Fabricating NPs using the typical techniques such as drop emulsion, microfluidics, or traditional nanoprecipitation can be expensive and may not yield the appropriate particle size. Therefore, a need has emerged for low-cost fabrication methods that allow customization of NP physical characteristics with high reproducibility. In this study we manufactured a low-cost (<$210), open-source syringe pump that can be used in nanoprecipitation. A design of experiments was utilized to find the relationship between the independent variables: polymer concentration (mg/mL), agitation rate of aqueous solution (rpm), and injection rate of the polymer solution (mL/min) and the dependent variables: size (nm), zeta potential, and polydispersity index (PDI). The quarter factorial design consisted of 4 experiments, each of which was manufactured in batches of three. Each sample of each batch was measured three times via dynamic light scattering. The particles were made with PLLA-mPEG dissolved in a 50% dichloromethane and 50% acetone solution. The polymer solution was dispensed into the aqueous solution containing 0.3% polyvinyl alcohol (PVA). Data suggests that none of the factors had a statistically significant effect on NP size. However, all interactions and relationships showed that there was a negative correlation between the above defined input parameters and the NP size. The NP sizes ranged from 276.144 ± 14.710 nm at the largest to 185.611 ± 15.634 nm at the smallest. In conclusion, the low-cost syringe pump nanoprecipitation method can achieve small sizes like the ones reported with drop emulsion or microfluidics. While there are trends suggesting predictable tuning of physical characteristics, significant control over the customization has not yet been achieved.

With an estimated 19.3 million cases and nearly 10 million deaths from cancer in a year worldwide, immunotherapies, which stimulate the immune system so that it can attack and kill cancer cells, are of interest. Tumors are produced from the uncontrolled and rapid proliferation of cells in the body. Cancer cells rely heavily on glutamine for proliferation due to its contribution of nitrogen for nucleotides and amino acids. Glutamine enters the tricarboxylic acid (TCA) cycle as α-ketoglutarate via glutaminolysis, in which glutamine is converted into glutamate by the enzyme glutaminase (GLS). Cancer cell proliferation may be limited by using glutaminase inhibitor CB-839. However, immune cells also rely on these metabolic pathways. Thus, a method for restarting the metabolic pathways in the presence of inhibitors is attractive. Succinate, a key metabolite in the TCA cycle, has been shown to stimulate the immune system despite the presence of metabolic inhibitors, such as CB-839. A delivery method of succinate is through microparticles (MPs) or nanoparticles (NPs) which may be coated in polyethylene glycol (PEG) for improved hydrophilicity. Polyethylene glycol succinate (PEGS) MPs were generated and tested in vivo and were shown to reduce tumor growth and prolong mouse survival. With the success in stimulating the immune system with MPs, NPs were investigated for an improved immune response due to their smaller size. These PES NPs were generated in this study. For clinical settings, it is necessary to scale-up the production of particles. Two methods of scale-up were proposed: (1) a combination of multiple small batches into a mixed batch, and (2) a singular, big batch. Size and release properties were compared to a small batch of PES NPs, and it was concluded that the big batch more closely resembled the small batch compared to the mixed batch. Thus, it was concluded that batch-to-batch variability plays a larger role than volume changes when scaling-up. In clinical settings, it is recommended to produce the particles in a big batch rather than a mixed batch.